How To Measure Trolling Motor Shaft Length

Jika anda sedang mencari How To Measure Trolling Motor Shaft Length, anda berada di tempat yang tepat! Disini saya akan mencoba membahas beberapa pertanyaan mengenai How To Measure Trolling Motor Shaft Length.

How do you measure trolling motor shaft?

Measure down from the mounting surface of the transom or bow to the water level. Add 5″ to waterline measurement for fishing in rough water. Add 12″ to waterline measurement for steering a hand control motor while standing. Use this measurement and the tables below to find the appropriate trolling motor shaft length.

Can a trolling motor shaft be too long?

However, if the shaft is too long, the propeller creates turbulence deep beneath the boat that will spook any nearby fish. And if the shaft is too short, the prop won’t be adequately submerged, which will create noisy chop in the water and also scare away the fish.

How do you size a Minn Kota trolling motor?

General rule of thumb: you need at least 2 lbs. of thrust for every 100 lbs. of fully-loaded boat weight (people and gear included). If things like wind or current are major factors where you fish, you’ll want a little extra thrust.

Can you change shaft length on trolling motor?

Always Go Long: If you’re struggling to decide between two lengths, pick the longer one. If the shaft ends up being a bit too long, you can always adjust the shaft depth upward with the depth collar adjustment found on nearly all trolling motors. But if you pick a shaft that’s too short, you’re simply out of luck.

How long should my trolling motor shaft be?

Measuring for your Correct Shaft Length Measure from the mounting surface of the transom or bow where the motor will be mounted to the top of the water and add 20″ to get the recommended minimum shaft length. If you will be fishing in rough water, add an additional 5″ to the measurement.

How do you tell if your boat needs a short or long shaft?

To do so, you will want to measure at the exact center of the transom from the very top to the very bottom. If it measures 15″ or with in a inch of that you will need a short shaft outboard. If it measures anywhere from 17″ to around 22″, then your going to want to go with a long shaft motor.

How far below the bottom of the boat should the prop be?

If you have a short shaft motor, the top most part of the transom and the lower most part of the boat should be about 15 to 16 inches.

How do you measure a transom?

Take a straight piece of wood, rod, or tubing the same length as the platform you desire. Mark the center of the straight edge, hold it level and square against the transom with the center marks matched. Measure from the ends of the straight edge to the transom.

How fast can a 50 lb thrust trolling motor go?

The maximum speed of a trolling motor is 5 mph regardless of how many pounds of thrust. The 55# thrust MinnKota Endura with all the new electronic gadgetry is overkill.

What does 55 lb thrust mean?

A 55-pound thrust motor will support a boat with a maximum weight of about 2500 pounds and a length of 21′

How deep should your trolling motor be in the water?

Setting your trolling motor at an appropriate depth will help it to function properly, while at the same time reducing the risk of it becoming damaged. Remember, the general rule is to keep the motor submerged 12 inches below the waterline.

Can you change Minn Kota shaft length?

For most of our motors, you can shorten the shaft of your trolling motor if it is too long. We recommend having the shaft shortened at an Authorized Service Center. If your motor is under warranty and you shorten the shaft yourself, it will void your warranty.

How long will a deep cycle battery run a trolling motor?

A marine battery will typically last for around 5 hours when running a trolling motor. However, this can vary depending on the age and condition of the battery, as well as other factors such as the weather.

What size battery do I need for a 55 lb thrust trolling motor?

Using a Newport Vessels 55lb thrust motor continuously for two hours at full speed would require a battery with a 100-120 AH rating.

Do trolling motors need grease?

Lubricating Your Trolling Motor Next time you give your boat a wash, don’t forget to lubricate your trolling motor shaft. This can be done after you have cleaned your trolling motor with water and a mild soap solution and wiped dry.

How do you store a trolling motor?

We do not recommend outdoor storage of your trolling motor in freezing temperatures. If you experience freezing temperatures, it is best to store the motor inside. If you must keep it outside, store it in a weather-protected area like a shed, underneath a porch under a tarp, etc.

Can you adjust depth of trolling motor?

Move the motor so that it stops halfway between the stowed and deployed positions. Loosen the collar at the base of the steering system housing. NOTE: You should be prepared for the motor to slide down when you loosen the collar. Raise or lower the depth of the trolling motor.

Can I use a long shaft on a short transom?

Re: Longshaft motor on a short transom skiff? It will will *run* fine, but it can cause bad handling. Also trim position settings will have a greater effect. No harm to try it, carefully, and see how it goes.

Can you put a 25 inch motor on a 20 inch transom?

You will get a definite performance drop using a 25″ shaft on a 20″ transom. Engine will be way too low. Options could be too lift the transom by building it up. If that is possible that will also help the low engine issue.

How long is a short shaft?

Short vs. Generally, short shaft outboards are 15 inches, long shaft outboards are 20 inches, and extra-long outboards are 25 inches.

How far below boat should cavitation plate?

The cavitation plate should be nearly even with or slightly below the bottom. For a short shaft the vertical measurement of the transom should be about 15 inches.

What happens if outboard is too high?

If it’s too high, the propeller tends to ventilate, losing its bite on the water and blowing out while turning and in steep seas. “If the prop consistently ventilates when heading down a steep wave, the outboard is probably set too high,” says Dean Corbisier, advertising and public relations manager for Suzuki Marine.

Should cavitation plate be underwater?

your cavitation plate should be right at the water level. As a rule of thumb it should be 1 inch above the hull for every 12 inches back. (if you have a eurotransom, or bracket or something.) If your cavitation plate is under water you might get better performance if you raise the motor.

What is the shortest trolling motor?

The shortest shaft available for the Motorguide xi3 saltwater trolling motor is 48″. Other than the longer shaft, the saltwater version of the xi3 has all the same features as the freshwater version.

Terimakasih telah membaca How To Measure Trolling Motor Shaft Length, semoga jawaban dari pertanyaan anda telah saya jawab semua. Semoga bermanfaat!